South Jersey

Install it, refinish it, or save it

Haddon Flooring installs solid and engineered hardwood, refinishes existing wood floors, and repairs boards down to matching discontinued hardwood. Because our team comes from real estate, we'll tell you straight whether to refinish, repair, or replace: the value case comes first, even when it means charging you less.

NJ HIC Reg. #13VH14108700 15 towns across 3 counties
Newly refinished red oak hardwood floors in a classic living room

Refinish-first approach

Save the wood you own before buying new

Three ways we work with wood

Install. Refinish. Repair.

Three different answers to the question, 'what should we do with the floors?'

New hardwood installation

Oak, hickory, maple, and walnut in the widths and layouts you want. Solid where moisture is controlled; engineered where stability matters. Nailed, glued, or floating, to the right spec for the room.

See engineered hardwood too

Refinishing & staining

Sanding, staining, and sealing returns tired, scratched, or smoke-aged floors to showroom condition. We also work with you on sheen and tone, from pale wire-brushed oak to rich walnut espresso.

Refinish or replace?

Repair & board replacement

Damaged boards, water-stained sections, and discontinued flooring get matched with harvested, salvaged, or re-milled wood, blended with stain so the patch disappears. No full-floor tear-outs required.

Discontinued? Start here
Herringbone-pattern engineered hardwood floor in a bright modern study

The hardwood decision

Solid vs. engineered, and when refinishing wins

The right answer depends on the room, the subfloor, and how long you'll live there. Here's the honest shorthand.

  • Refinish first, almost always

    If the wood is solid and thick, refinishing returns the look for a fraction of replacement cost. We check before we ever recommend tearing out.

  • Solid for dry main levels

    In climate-controlled rooms over a wood subfloor, solid hardwood delivers maximum life and the strongest resale signal.

  • Engineered for slabs and basements

    Where solid wood can't go, engineered hardwood can, staying flat over concrete and radiant heat.

  • Moisture decides basements

    Below grade, even engineered wood needs dry-enough conditions. When they're not there, we say so and recommend waterproof flooring instead.

Answers first

Hardwood flooring FAQs

Can my existing hardwood floors be refinished?

In most cases yes. If the boards are solid and thick enough to sand, we can refinish them, which means repairing damaged boards, matching discontinued sections when needed, and sanding, staining, and sealing for a like-new surface at a fraction of replacement cost.

What's the difference between solid and engineered hardwood?

Solid hardwood is one piece of wood, typically 3/4 inch thick, that can be refinished many times. Engineered hardwood is a real wood wear layer bonded to a stable plywood core, so it holds up on slabs, in basements, and over radiant heat where solid wood can't go.

How much does hardwood installation cost?

National guides typically put installed solid hardwood between $8 and $25 per square foot, with most mid-range work from $10 to $20. The actual price depends on species, plank width, subfloor condition, removal, and stairs, which is why we measure before quoting.

What should I do if my hardwood is discontinued?

Don't panic and don't rip anything out. We harvest matching boards from closets and under stairs, source salvage, and blend stain so the repair disappears. Most floors can be fixed invisibly.

How long does a hardwood refinishing project take?

A typical room takes a few days, including sanding, staining, and multiple coats of finish with drying time between. We give you the exact timeline with your estimate.

Can hardwood go in a basement?

Solid hardwood should not go below grade. Engineered hardwood can work on slab in the right conditions, but for genuinely damp South Jersey basements, waterproof flooring is the safer recommendation.

Free estimates

See what your hardwood is worth saving

We inspect the wood, measure the job, and give you the honest math on refinish, repair, or replace. Written estimate, no pressure.

Start here

Get your hardwood estimate

Whether it's new wood, a refinish, or a repair, the first step is a look at the actual floor. Call (856) 654-0005 or send the form and we'll schedule your measure.

Request your free estimate

Tell us about your project and we'll come back with next steps, including a free in-home measure.

[GHL CALENDAR: In-Home Measure]

Schedule your in-home measure once the calendar embed is connected.